#Upgrade memory in imac 2011 install#

Move the DIMM ejector clips to their fully open position:.

Using a Phillips screwdriver, remove the RAM access door on the bottom of the iMac and set it aside:.

There should be a slight click when you seat the memory correctly.

After you insert it, press the DIMM up into the slot.

Insert your new or replacement RAM SO-DIMM into the empty slot, noting the orientation of the keyway of the SO-DIMM as shown above.

If you're replacing a memory module, untuck the tab and pull it to eject any installed memory module:

Untuck the tab in the memory compartment.

Using a Philips screwdriver, remove the RAM access door in the bottom of the computer:.

Tuck the tabs above the memory DIMMs, and reinstall the memory access door:ДЄfter your iMac cools down, follow these steps:.

There should be a slight click when you seat the memory correctly:

Insert your new or replacement SO-DIMM into the empty slot, noting the orientation of the keyway of the SO-DIMM as shown below.

If you're replacing a memory module, gently pull the tab to eject any installed memory module:

Remove the access door and set it aside.

Using a Philips screwdriver, remove the RAM access door in the bottom of your computer:.

Make sure to let the memory initialization complete. This process can take 30 seconds or more, and the display of your iMac remains dark until it's finished. Your iMac performs a memory initialization procedure when you first turn it on after upgrading memory or rearranging DIMMs. Reconnect the power cord and all other cables to the computer, then start up the computer.

Place the computer in its upright position.

You don't need to press the compartment door release button when replacing the compartment door.

#Upgrade memory in imac 2011 install#

After you install all of your DIMMs, push bothВ memory cage levers back into the housing until theyВ lock into place:.

iMac (27-inch, Late 2013) and iMac (Retina 5K, 27-inch, Late 2014, Mid 2015, and Late 2015) DIMMs have aВ notch on the bottom right:.

iMac (27-inch, Late 2012) and iMac (Retina 5K, 27-inch, 2017) DIMMs haveВ a notch on the bottom left:.

iMac (Retina 5K, 27-inch, 2019) DIMMs have a notch on the bottom, slightly left of the middle:.

If your DIMMs are mixed in capacity, minimize the capacity difference between Channel A (slots 1 and 2) and Channel B (slots 3 and 4) when possible.

iMac (Retina 5K, 27-inch, 2020) DIMMs have a notch on the bottom, slightly left of the middle.

Find your model below for specific installation instructions and notch locations:

When you insert a DIMM, make sure to align the notch on the DIMM to the DIMM slot. Replace or install a DIMM by setting it down into the slot and pressing firmly until you feel the DIMM click into the slot.When reinstalling DIMMs, the notch must be oriented correctly or the DIMM won't fully insert: Remove a DIMM by pulling the module straight up and out.В Note the location of the notch on the bottom of the DIMM.After the memory cage is released, pull the memory cage levers toward you, allowing access to each DIMM slot.Push the two levers outward to release the memory cage: Locate the two levers on the right and left sides of the memory cage. AВ diagram on the underside of the compartment door shows the memory cage levers and the orientation of the DIMM.Remove the compartment door and set it aside: The memory compartment door will open as the button is pushed in.Open the memory compartment door by pressing the small grey button located just above the AC power port:.Hold the sides of the computer and slowly lay the computer face-down on the towel or cloth.Place a soft, clean towel or cloth on the desk or other flat surface to prevent scratching the display.Disconnect the power cord andВ all other cablesВ from your computer.

If you've been using your iMac, wait ten minutes after shutting it down to let the internal components cool.ДЄfter you shut down your iMac and give it time to cool, follow these steps: The internal components of your iMac can be warm.